Want to see correct answers?
Login or join for free!
  printable Worksheets
Looking for printable worksheets?
Check out our pre-made printable worksheets!
Share/Like This Page
Filter By Grade

You are browsing Continuing Education questions. View questions in All Grades.

Grade 9 Grade 10 Grade 11 Grade 12 College Continuing Education

Browse Questions

Continuing Education Carpentry Questions

You can create printable tests and worksheets from these Continuing Education Carpentry questions! Select one or more questions using the checkboxes above each question. Then click the add selected questions to a test button before moving to another page.

Previous Page 2 of 17 Next
Continuing Education Types of Drawings Used in Carpentry
When contour lines on a drawing are close together what does it tell you about the property?
  1. The property is steep
  2. The property has a gradual slope
  3. The property has good drainage
  4. The property has a lot of extra fill
Continuing Education Blueprints and Blueprint Reading
In which blueprint would you find the specifications for the type of siding that is used on a building?
  1. Architectural
  2. Structural
  3. Mechanical
  4. Electrical
Continuing Education Hand Tools
What can be done to a nail to reduce the chance of the material splitting?
  1. Cut off the point
  2. Blunt the point by hitting it with a hammer
  3. Hammer really slowly
  4. Hammer really lightly
Continuing Education Power Tools
When cutting an circle into a cabinet made of 5/8" MDF what is the best tool to use?
  1. Jig saw
  2. Recipricating saw
  3. Skill saw
  4. Utility knife
Continuing Education Hand Tools
If you are having difficulty pulling a nail from a piece of material, what is the most efficient way to increase the leverage of the hammer you are using?
  1. Add a block under the hammer
  2. Add a pipe to the end of the hammer
  3. Use a different hammer
  4. Drive the nail in until it protrudes to the other side
Continuing Education Problem Solving
New drywall is installed on existing studs in a building. There are numerous nail pops happening one month after the installation. What is the most common cause of this?
  1. Studs should have been removed and reinstalled new ones
  2. Wrong drywall was used
  3. Wood was wet when drywall was installed
  4. Drywall was not installed tight to the studs
Continuing Education Types of Wall and Ceiling Finishes
Suspended ceiling panels have minimal options for panel types and finishes.
  1. True
  2. False
Continuing Education Surveying and Plot Plans
A contour line identifies the
  1. size of the land.
  2. slope and elevations of the land.
  3. direction of the land.
  4. direction of the water flow on the land.
Continuing Education Hand Tools
When clamping material together, what is something that needs to be avoided to prevent damaging of material?
  1. Over clamping, which causes dents
  2. Using the wrong clamp
  3. Under clamping, which doesn't create a sufficient hold
  4. All of the above
Continuing Education Hand Tools
What are the two most common types of claw hammers that are used in carpentry?
  1. Framing
  2. Finishing
  3. Straight
  4. Roofing
Continuing Education Hand Tools
What tool would give you the most accurate reading when measuring board thickness?
  1. Metal ruler
  2. Speed square
  3. Tape measure
  4. Caliper
Continuing Education Blueprints and Blueprint Reading
In which blueprint would you find specifications about the plumbing?
  1. Architectural
  2. Structural
  3. Mechanical
  4. Electrical
Continuing Education Hand Tools
This type of level is small and used to check areas for plumb or level that would not require a 2' or 4' level.
  1. Mini level
  2. Torpedo level
  3. Small level
  4. Hand level
Continuing Education Blueprints and Blueprint Reading
Which drawing would you refer too when determining how to fasten the sill plate to foundation wall?
  1. Detail
  2. Floor plan
  3. Cross section
  4. Elevation
Continuing Education Hand Tools
Which of the following types of clamps will do the least damage to material when applying pressure?
  1. Spring clamp
  2. Bar clamp
  3. Band clamp
  4. Edge clamp
Continuing Education Building Materials
Which of the following type of engineered panel is considered structural?
  1. Particle board
  2. Medium density fibreboard
  3. Plywood
  4. Oriented strand board
Previous Page 2 of 17 Next