Want to see correct answers?
Login or join for free!
  printable Worksheets
Looking for printable worksheets?
Check out our pre-made printable worksheets!
Share/Like This Page
Filter By Grade

You are browsing Continuing Education questions. View questions in All Grades.

Grade 9 Grade 10 Grade 11 Grade 12 College Continuing Education

Browse Questions

Continuing Education Carpentry Questions

You can create printable tests and worksheets from these Continuing Education Carpentry questions! Select one or more questions using the checkboxes above each question. Then click the add selected questions to a test button before moving to another page.

Previous Page 4 of 17 Next
Continuing Education Power Tools
When required to drill a hole 3/4 of the way through a piece of material, what is the best drill bit to use?
  1. Auger bit
  2. Countersink bit
  3. Forstner bit
  4. Twist bit
Continuing Education Concrete Forming Systems and Techniques
When pouring a concrete slab on grade at the same time as the footing, it is referred to as a                 slab.
  1. Single
  2. Monolithic
  3. Full
  4. One time
Continuing Education Hand Tools
When cutting a piece of drywall to fit in place, what tool is used to score the drywall?
  1. Hand saw
  2. Drywall saw
  3. Utility knife
  4. Swiss army knife
Continuing Education Types of Drawings Used in Carpentry
What is the name of the lines on a topographical drawing that show different elevations of existing and finished grade lines of a piece of property?
  1. Landscape lines
  2. Grid lines
  3. Plot lines
  4. Contour lines
Continuing Education Architectural Features and Trim
Baseboard trim should be                 than the door casing.
  1. Thicker
  2. Thinner
  3. Wider
  4. Longer
Continuing Education Problem Solving
New cabinetry is installed in a existing kitchen. The distance between the edge of the wall and the cabinet varies by 1/2" from the top to the bottom. What is the most cost effective solution to "hide" this?
  1. Reframe the entire wall system to make it level
  2. Provide a gap 1" on the large side and fill the gap in with a filler strip
  3. Remove the cabinetry and build the last cabinet at an angle
  4. Leave a gap between the cabinet and the wall
Continuing Education Replacing Windows and Doors
When renovating a house and you are required to replace all of the windows, doors and siding on the building. What is the most efficient system to use to do this?
  1. Ladders
  2. Perimeter scaffold
  3. Scissor lift
  4. They would all take the same amount of time
Continuing Education Power Tools
When cutting a full 4' x 8' sheet of plywood into a strips 12" wide what is the best tool to use?
  1. Table saw
  2. Jig saw
  3. Recipricating saw
  4. Hand saw
Continuing Education Hand Tools
To maximize the striking force when using a hammer the user should hold the hammer on the                        .
  1. Top
  2. End of the handle
  3. Top of the handle
  4. Below the striking face
Continuing Education Exterior Installation Techniques and Terminology
Additional building papers such as asphalt tar paper are used on the exterior face of sheathing to prevent the intrusion of water. What other product is used for this purpose.
  1. Tyvec
  2. Stryofoam
  3. Clear cedar siding
  4. Concrete base siding
Continuing Education Retrofitting Solutions
What is the main areas air leakage occurs in a house? These areas should be paid attention to by the carpenter to ensure adequate sealing of the building envelope.
  1. Around doors and windows
  2. Through the framing members
  3. Through the roof
  4. Through the plumbing
Continuing Education Hand Tools
What type of saw is used to cut along the grain of wood?
  1. Cross cut saw
  2. Rip saw
  3. Miter saw
  4. Coping saw
Continuing Education Concrete Forming and Placing Tools
A screed board needs to be made out of magnesium or aluminum for it to work correctly.
  1. True
  2. False
Previous Page 4 of 17 Next